Project Description
CYS Series
| Six Models | |
| CYS-C1 |
Max pressure：8.0Bar； Max power：380V 7.5KW
|
| CYS-C2 |
Max pressure：8.0Bar； Max power：380V 15.0KW
|
| CYS-C3 |
Max pressure：8.0Bar； Max power：230V 7.5KW
|
| CYS-C4 |
Max pressure：15.0Bar； Max power：380V 7.5KW
|
| CYS-C5 |
Max pressure：15.0Bar； Max power：380V 15.0KW
|
| CYS-C6 |
Max pressure：15.0Bar； Max power：230V 7.5KW
|
1.FUNCTION INTRODUCTION
| 1.1 | Automatic detection of three-phase line order to prevent equipment from reverse. |
| 1.2 | Automatic detection of missing phase. |
| 1.3 | Real-time monitoring of pressure, current and voltage. |
| 1.4 | Real-time monitoring of over-voltage, under-voltage and over-current. Abnormal immediately alarm, display specific alarm reasons. |
| 1.5 | Pressure range can be set as required. |
| 1.6 | Two pressure units(Bar/Psi) can be free to switch. |
| 1.7 | Display equipment running time. |
| 1.8 | Automatic exhaust valve. |
| 1.9 | Cumulative work more than 8 hours, equipment automatic drainage. |
| 1.10 | Automatic reminder of low oil level. |
2. INSTALLATION GUIDE
WIRING DIAGRAM OF CONTROLLER
| 2.1 | Install the sensor:The Lead end of sensor must be installed face up. |
| 2.2 | Wiring: Open both sides of the yellow cover area, wiring in strict accordance with the wiring diagram. (24V NC type exhaust solenoid valve should be selected.) |
| 2.3 | First start: All valves must be closed. Open the equipment to achieve the maximum pressure, then can be used for normal use.(If there is the alarm phenomenon of over-current, locked-rotor and so on for the first time to start the equipment, reset to the factory settings before the operation above.) |
3. OPERATION PANEL & BUTTONS
3.1 OPERATION PANEL INTRODUCTION
OPERATING PANEL
| 1 Power key |
| 2 “↑”key |
| 3 “↓”key |
| 4 Pressure unit |
| 5 Current air pressure |
| 6 Running state |
| 7 Running time |
| 8 The current |
| 9 Cause of failure |
3.2 BUTTONS INTRODUCTION
| 3.2.1 | Setup interface: Long press the “start/stop” button and “↓” key 6s at the same time to show setup interface. Click the “start/stop” button to switch settings. |
| 3.2.2 | Save settings: a) Long press the “start/stop” button and “↓” key 6s at the same time to save the parameters. b) After setting the parameters, wait for 20s, it will automatically exit from the setup interface and save the parameters. |
| 3.2.3 | Remove alarm: Click “start/stop” button to remove the alarm. |
| 3.2.4 | Switch pressure unit: Click the “↓” key to switch pressure unit ( Bar /Psi). |
| 3.2.5 | Factory setting: Long press the three buttons 6s at the same time to restore the factory default settings. |
| 3.2.6 | View the reference current: Long press “↑” to view the reference current. |
| APPENDIX: | POWER &AIR PRESSURE SETTING INTERFACE ILLUSTRATION, INDEX VALUE & SETTING PARAMETERS RELATIONAL TABLES |
POWER SETTING INTERFACE
【1.Index value 2.Power setting value 】
AIR PRESSURE SETTING INTERFACE
【1.Index value 2.Pressure setting value 】
| Index value | Setting parameters |
| 0 |
Power(KW)setting：0（Default）
/1.00/1.10/1.20/…/7.40/7.50/…/14.90/15.00
|
| 1 | Set maximum pressure：8Bar（Default） |
| 2 | Set minimum pressure：6Bar（Default） |
| 3 | Pressure unit：1（Default）stands for Bar，2 stands for Psi |
index value and setting parameters
4.ALARM PHENOMENON
| 4.1 Line order alarm: |
| “LO” lights up when line order error is happened. It can not be turned on and interface turns red when the alarm occurs. Buzzer blaring. |
| 4.2 Missing phase alarm: |
| “DP” lights up when missing phase is happened. It can not be turned on and interface turns red when the alarm occurs. Buzzer blaring. |
| 4.3 Over current alarm: |
| After being turned on, if the current abnormally increases, “OC” lights up. Shut down and interface turns red when the alarm occurs. Buzzer blaring. |
| 4.4 Oil level alarm: |
| when the oil pressure over lowering in power-on state, “OL” lights up, Shut down and interface turns red when the alarm occurs. Buzzer blaring. |
| 4.5 Other alarm: |
| When being turned on for first time, if no increase in pressure or current abnomality, shut down and alarm. Screen flickers three times and buzzer short sounds three times. |
5. SECURITY MATTERS
| 5.1 Reminder: |
| Be sure to note the following safety rules in all processes using this controller. The company shall not be responsible for any personal injury or property loss as a result of violation of the provisions. |
| 5.2 Do not operate in an explosive environment. |
| Do not use the instrument in place where there are flammable and explosive materials. In this environment, the use of any electrical equipment are likely to cause harm to safety. |
| 5.3 Wiring in strict accordance with the drawings |
| Wiring in strict accordance with the drawings, It is forbidden to connect multiple air-end to the same terminal. |
| 5.4 Earth wire |
| Ensure that the earth wire is connected before turn on the power to prevent electric shock. |
| 5.5 Power supply |
| Energize the controller and ensure that the supply voltage matches the rated voltage. |
| 5.6 Please do not remove any shell part without authorization |
| It works with high voltage in some parts of the controller, do not take off the controller shell or any part of the controller mainboard without special permission. |